• Training
    • Injury Prevention
    • Training Tips
  • How To
    • Bike Fit
    • Gear
  • Nutrition
    • Nutrition Tips
    • Weight Loss
  • Repair
  • Reviews
  • Stories
    • Funny Stories
    • Jokes
    • Quotes
    • Videos
    • Funny Videos

I Love Bicycling

I Love Bicycling is a website that is geared towards cycling for beginners with road cycling tips, training articles, nutrition tips, weight loss, how to’s and bike repair articles.

How To Fix Sloppy Bike Steering

August 31, 2020 by Sarah Lauzé

You may have noticed a clunking noise in your front end. You might feel a bit of play in your steering. You might notice more vibration than you think is normal. All of these symptoms are typical of loose bike headsets. Bike steering adjustments are routine, and nothing you can’t handle yourself.
Bike Steering

Bike Steering

Bike steering is made possible by your headset. The headset is a rotating joint at the bottom of the stem. It allows the steering column (tube) and front wheel to rotate and turn. The headset is your focus for bike steering issues. All you need to fix it is your multi-tool, or alternatively a 4-mm, 5-mm or 6-mm hex wrench, depending on model of bike. Tightening your headset is one of the most basic of all bike maintenance procedures.

Quick Test For a Loose Headset

If you’re not sure about bike steering or your headset, a quick test will help you decide if it needs attention, here’s how to do it: Apply pressure to your front brake by squeezing the lever. Place your other hand on the front of the stem, just above the fork. Rock the bike forward and back. If you feel a slight knocking your headset is loose. If you look close, you may even be able to see a slight separation (very slight) between the steering tube and the bushing when you rock the bike. A loose headset may also produce a more dramatic clunking sound when you bounce the front tire, or if you hit a bump when riding. That sharp clunk when you pass over railroad tracks is a perfect example.

Step One: Loosen the Pinch Bolts

Your bike should have two pinch bolts (some people call them stem clamp bolts) located on the vertical part of the stem facing the seat.  The bolts are horizontal and perpendicular to the top tube, and a critical part of bike steering. Note that one bolt typically enters the stem from the left, and the other from the right. Loosen them just enough so that the stem goes slack, or that you can move the handlebars without turning the wheel. Start with the 5-mm hex wrench, if it doesn’t fit, use the 4-mm or the 6-mm.

Step Two: Tighten the Headset

Tighten the large, vertical bolt (aka pre-load bolt) on the top cap of the stem using the 5 or 6-mm hex wrench. This is important: tighten it only enough to take the play out of the headset. The tightening motion squeezes the parts together (bearing tension) inside the headset, if you get them too tight, your bike steering will be stiff, and it will wear out the headset. In most cases, you won’t need to tighten the bolt more than about 1/4-to-1/2-turn. If you think you’ve over-tightened it, back it off a 1/4-turn.

Step Three: Test It

Grasp the front brake, and rock the bike forward and back. If you hear a clunking it’s not tight enough. If you’re not sure, do the test with your hand on the front of the stem. When you’re satisfied, go to Step four.

Step Four: Align The Handlebars

Your bike steering is still loose at this point. Stand over the bike and do a visual straightening of the handlebars. One way is to center the drop-outs (the ends of the axle on the front tire) with the center of the stem. Or you can just use the tire. This can be tricky, but easy to adjust later if you’ve tweaked it the wrong way. When you’re satisfied that the handlebars are straight, tighten the pinch bolts. These bolts need to be tight, they’re the only thing securing your stem to the steering tube.

Torque and Carbon

Something should be said about over-tightening bolts on bikes, especially carbon-fiber bikes. Even a slight miscalculation in torque can be a very expensive mistake on a carbon fiber frame. That sickening crunch can literally cost you thousands. Here’s how to avoid it: Invest in a bicycle specific torque wrench. A majority of carbon fiber bikes require a setting of 5nM. (newton meters) Using the torque wrench won’t allow you to ruin your carbon fiber frame, because you’ve set it according to manufacture’s instructions. (Don’t use the torque wrench to tighten the top cap bolt on your headset though, that’s a feel thing — unless specified to do so by your bike’s manufacterer).

Check With A Mechanic

If you’re not sure about any of your bolts torque requirements, or  how your bike steering mechanism (headset), works, check with your bike’s manufacturer or local mechanic. For extra help, check out the video below!

Filed Under: Bike Fit, How To, Repair Tagged With: bike handling, bike maintenance, bike steering

  • Facebook
  • Tumblr
  • Twitter

Latest Articles

JOIN Cycling: A New Training Platform for Cyclists

May 27, 2024 By Eric Lister

cold exposure

The Benefits of Cold Exposure for Cycling & Life

June 13, 2023 By Eric Lister

hill climb

The Ultimate Hill Climb Training Guide

May 31, 2023 By Eric Lister

shoulder pain cycling

How to Treat & Avoid Shoulder Pain While Cycling

April 12, 2023 By Eric Lister

psoas stretch

The Importance of the Psoas Stretch for Cyclists

April 6, 2023 By Eric Lister

cycling neck pain

The Ultimate Guide to Cycling Neck Pain: Causes and Solutions

March 21, 2023 By Eric Lister

Useful Info

  • Contact
  • Finally, A Global Cycling Club That Is Focused On Community And Love Of Cycling!
  • Privacy Policy
  • Share Your Story!
  • Terms And Conditions Of Use
  • Welcome to I Love Bicycling
  • What Happened When I Stretched Every Day For a Month

Recent Posts

  • JOIN Cycling: A New Training Platform for Cyclists
  • How to Hang Bikes in Your Garage: 4 Inexpensive Options
  • Gravel Bike Vs. Road Bike: Which One Is Better For You?
  • The 6 Types of Mountain Bikes & How to Choose the Best One for You
  • What Is a Touring Bike Good For? 5 Benefits We Know You’ll Love

Search I Love Bicycling

Connect with Us

  • Facebook
  • RSS
  • Tumblr
  • Twitter

Copyright © 2025 · Magazine Pro Theme on Genesis Framework · WordPress · Log in